SP Mode Ricoh AFICIO MP4000/5000

Service Table Key

Notation What it means
[range / default / step]Example: [-9 to +9 / 0 / 0.1 mm step]. The setting can be adjusted in
the range ±9, value reset to +3.0 after an NVRAM reset, and the value
can be changed in 0.1 mm steps with each key press.
* Value stored in NVRAM. After a RAM reset, this default value (factory
setting) is restored.
MS Monochrome Scanner Model: D009/D012
CS Color Scanner Model: D011/D013
DFU Denotes “Design or Factory Use”. Do not change this value.
Japan only The feature or item is for Japan only. Do not change this value.
C1b 40 cpm: D009/D011
C1c 50 cpm: D012/D013
SSP This denotes a “Special Service Program” mode.

SP1-xxx: Feed-1

1001*Leading Edge Registration:
Adjusts the leading edge registration by changing the registration clutch operation timing
001 Tray: Plain[–9 to 9/ 0 / 0.1 mm step]
002 Tray: Thick 1[–9 to 9/ 0 / 0.1 mm step]
003 Tray: Thick 2[–9 to 9/ 0 / 0.1 mm step]
004 By-pass: Plain [–9 to 9/ 0 / 0.1 mm step]
005 By-pass: Thick 1 [–9 to 9/ 0 / 0.1 mm step]
006 By-pass: Thick 2 [–9 to 9/ 0 / 0.1 mm step]
007 Duplex: Plain [–9 to 9/ 0 / 0.1 mm step]
008 Duplex: Thick 1 [–9 to 9/ 0 / 0.1 mm step]
1002*Side-to-Side Registration
Adjusts the side to side registration by changing the laser main scan start position for each
mode.
001 By-pass[–4 to 4/ 0 / 0.1 mm step]
002 Tray 1
003 Tray 2
004 Tray 3
005 Tray 4
006 LCT
007 Duplex
1003* Registration Buckle Adjustment
Adjusts the paper feed motor timing. Paper feed motor timing determines the amount of
paper buckle at Registration. (A “+” setting causes more buckling.)
001 Tray 1: Plain
[-9 to 5 / -4 / 1 mm step
002 Tray 1: Thick 1 [-9 to 5 / -4 / 1 mm step
003 Tray 1: Thick 2 [-9 to 5 / -4 / 1 mm step
004 Tray 2, 3, 4: Plain [-9 to 5 / -4 / 1 mm step
005 Tray 2, 3, 4: Thick1 [-9 to 5 / -4 / 1 mm step
006 Tray 2, 3, 4: Thick2 [-9 to 5 / -4 / 1 mm step
007 By-pass: Plain[-9 to 5 / -2 /1 mm step]
008 By-pass: Thick 1 [-9 to 5 / -2 /1 mm step]
009 By-pass: Thick 2 [-9 to 5 / -2 /1 mm step]
010 Duplex: Plain [-9 to 5 / -4 / 1 mm step]
011 Duplex: Thick 1 [-9 to 5 / -3 / 1 mm step]
012 LCT: Plain[-9 to 5 / -4 / 1 mm step]
013 LCT: Thick1 [-9 to 5 / -4 / 1 mm step]
014 LCT: Thick2 [-9 to 5 / -4 / 1 mm step]
1007*By-pass Paper Size Detection
Controls paper size detection for the by-pass feed table.
1007 1 Detection Timing [-15 to 15 / 0 / 5 mm step]
1007 2 LG Detection[0 to 1 / 0 / 1]
0: LT SEF, 1: LG
1103*Fusing Idling
Switches fusing idling on/off. When on, printing will not start until enough time has
elapsed so the hot roller can reach optimum temperature. This ensures even heat on the
hot roller.
Switch on if fusing on the 1st and 2nd copies is incomplete (this may occur if the room is
cold.). You must switch SP1103-1 ON before you set the fusing interval with SP1103-2
001 Enable Fusing Idling 0 = Off, 1 = On
002 Interval [0 to 60 / 30 / 1 sec.]
00 3 Idling Time at Every Job Sets the machine to fusing idling only for 30 sec. for
every job (when the original is set on the ARDF, when
the ARDF cover is opened, etc.) and the fusing unit has
reached the reload temperature (optimum
temperature for operation).
[0 to 30 / 0 / 1 sec.]
0: No idling done before a job.
1004*Fusing Temperature Control
On-Off/Phase
Selects the fusing temperature control method. After changing this setting, be sure to turn
the machine off and on again with the main power switch to enable the new setting.
[0 to 1 / 0 / 1]
0: Normal (ON/OFF control). Allows full application from ac power supply to bring the
hot roller up to the target fusing temperature then shuts off. Determines the on-time from
the present temperature (detected by the thermistor on the hot roller) and the temperature
of 1 cycle before.
1: Phase (hysterisis) control. Sets the upper and lower limits for the temperature; at the
lower temperature the fusing lamp is on and at the higher temperature the fusing lamp is
off.
Change this setting to “0” only if the user has excessive electrical noise or interference
on the power supply line. Such interference can cause voltage to drop when power is
applied using the ON/OFF control method.
Interference can be caused by the general poor quality of the power supply lines, or if
the machine is sharing a power supply with other electrical devices such as fluorescent
lights. Before changing this setting, make sure that the machine is connected to a power
supply not shared by other electrical equipment.
Note
• Selecting Phase control (“1”) could cause the fusing temperature control board to
emit low pitched noise
1005*Fusing Temperature Adjustment
Allows adjustment of the hot roller temperature at the center and ends of the roller for the
quality or thickness of the paper. The hot roller in this machine has two fusing lamps: one
heats the center of the roller, the other heats both ends. Each fusing lamp can be adjusted
separately
The “re-load temperature” is the “print ready temperature”. When the fusing temperature
exceeds this setting, the machine can operate. Do not set up a re-load temperature (Re
load Temp. = Fusing. Temp – SP Value.) that is higher than the SP1-105-2 setting.
001Roller Center
C1b: [100 to 170 / 140 / 1 deg]
C1c: [100 to 170 / 150 / 1 deg]
Adjusts the fusing temperature at the center of the hot roller.
002Roller Ends
C1b: [100 to 170 / 145 / 1 deg]
C1c: [100 to 170 / 155 / 1 deg]
Adjusts the fusing temperature at the ends of the hot roller.
003Re-load Temp. Minus: Roller Center
[0 to 60 / 0 / 1 deg]
Sets the reload temperature for the center of the hot roller. This setting depends on the target
temperature.
Reload temp. = Target Temp – This SP Setting
Note
• Do not set a temperature that is higher than the setting for SP1105 1 (Roller Center:
Trays)
004Re-load Temp. Minus: Roller Ends
[0 to 60 / 0 / 1 deg]
Sets the reload temperature for the ends of the hot roller. This setting depends on the target
temperature.
Reload temp. = Target Temp – This SP Setting
Note
• Do not set a temperature that is higher than the setting for SP1105 2 (Roller Ends:
Trays)
005-020The following SPs adjust the fusing temperature at the center or ends of the hot roller for
each paper type.
005Roller Center: M-Thick
C1b: [100 to 170 / 145 / 1 deg]
C1c: [100 to 170 / 155 / 1 deg]
006Roller Ends: M-Thick
C1b: [100 to 170 / 150 / 1 deg]
C1c: [100 to 170 / 160 / 1 deg]
007Roller Center: Thick 1
[100 to 170 / 130 / 1 deg
008Roller Ends: Thick 1
[100 to 170 / 130 / 1 deg
009 Roller Center: Thick 2 [100 to 170 / 150/ 1 deg]
010 Roller Ends: Thick 2 [100 to 170 / 150/ 1 deg]
011 Roller Center: ThinC1b: [100 to 170 / 130 / 1 deg]
C1c: [100 to 170 / 140 / 1 deg]
012 Roller Ends: ThinC1b: [100 to 170 / 135 / 1 deg]
C1c: [100 to 170 / 145 / 1 deg]
013 Roller Center: OHP: Plain [100 to 170 / 150/ 1 deg]
014 Roller Ends: OHP: Plain[100 to 170 / 155/ 1 deg]
015 Roller Center: OHP: Thick [100 to 170 / 155/ 1 deg]
016 Roller Ends: OHP: Thick [100 to 170 / 160/ 1 deg]
017 Roller Center: Special 1C1b: [100 to 170 / 140 / 1 deg]
C1c: [100 to 170 / 150 / 1 deg]
018 Roller Ends: Special 1 C1b: [100 to 170 / 145 / 1 deg]
C1c: [100 to 170 / 155 / 1 deg
019 Roller Center: Special 2 C1b: [100 to 170 / 140 / 1 deg]
C1c: [100 to 170 / 150 / 1 deg]
020 Roller Ends: Special 2 C1b: [100 to 170 / 145 / 1 deg]
C1c: [100 to 170 / 155 / 1 deg
021 Roller Center: Special 3 C1b: [100 to 170 / 140 / 1 deg]
C1c: [100 to 170 / 150 / 1 deg]
022 Roller Ends: Special 3 C1b: [100 to 170 / 145 / 1 deg]
C1c: [100 to 170 / 155 / 1 deg
023 Feed Waiting: Plain Turns the feed waiting mode on or off for each
paper type.
[0 to 1 / 0 / 1]
0=Off, 1=On
The paper waits at the registration roller until the
fusing temperature reaches the prescribed
temperature (adjustable with SP1105-028 to
-37). If you enable this feature, also set SP 1105-38
to a convenient value for the customer.


024 Feed Waiting: M-Thick Turns the feed waiting mode on or off for each
paper type.
[0 to 1 / 0 / 1]
0=Off, 1=On
The paper waits at the registration roller until the
fusing temperature reaches the prescribed
temperature (adjustable with SP1105-028 to
-37).
If you enable this feature, also set SP 1105-38
to a convenient value for the customer.
025 Feed Waiting: Thick 1 Turns the feed waiting mode on or off for each
paper type.
[0 to 1 / 0 / 1]
0=Off, 1=On
The paper waits at the registration roller until the
fusing temperature reaches the prescribed
temperature (adjustable with SP1105-028 to
-37)
If you enable this feature, also set SP 1105-38
to a convenient value for the customer. .
026 Feed Waiting: Thick 2 Turns the feed waiting mode on or off for each
paper type.
[0 to 1 / 0 / 1]
0=Off, 1=On
The paper waits at the registration roller until the
fusing temperature reaches the prescribed
temperature (adjustable with SP1105-028 to
-37)
If you enable this feature, also set SP 1105-38
to a convenient value for the customer. .
027 Feed Waiting: Thin Turns the feed waiting mode on or off for each
paper type.
[0 to 1 / 0 / 1]
0=Off, 1=On
The paper waits at the registration roller until the
fusing temperature reaches the prescribed
temperature (adjustable with SP1105-028 to
-37)
If you enable this feature, also set SP 1105-38
to a convenient value for the customer. .
028 Feed Wait: Center Minus: Plain Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
029 Feed Wait: Center Minus: Plain Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
030 Feed Wait: Center Minus: M-Thick Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
031 Feed Wait: Ends Minus: M-Thick Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
032 Feed Wait: Center Minus: Thick 1 Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
033 Feed Wait: Ends Minus: Thick 1
Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
034 Feed Wait: Center Minus: Thick 2 Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
035 Feed Wait: Ends Minus: Thick 2 Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
036 Feed Wait: Center Minus: Thin Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
037 Feed Wait: Ends Minus: Thin Adjusts the offset value for each re-load
temperature to exit the feed waiting mode.
[0 to 60 / 0 / 1 deg]
038 Feed Waiting: Maximum TimeSets the maximum feed waiting time.
[0 to 30 / 0 / 1 sec]
The paper is fed when the time specified with
this SP has passed even though the fusing
temperature has not reached the prescribed
temperature.
0: Disabled.
1106 Fusing Temperature Display
001 Roller Center Displays the temperature of the fusing unit.
[-20 to 250 / 0 / 1 deg]
002 Roller Ends Displays the temperature of the fusing unit.
[-20 to 250 / 0 / 1 deg]
003 Machine Inside at Power On Displays the temperature inside the machine.
[-20 to 250 / 0 / 1 deg]
004 Machine Inside Displays the temperature inside the machine.
[-20 to 250 / 0 / 1 deg]
1109*Fusing Nip Band Check
Checks the fusing nip band
001Execution
002Idling Rotation Time
[0 to 120 / 60 / 1 sec]
Specifies the fusing rotation time before executing SP1109-001.
003 Pre-Idling Time
[5 to 30 / 10 / 1 sec]
Specifies the time that the paper stops in the fusing unit for measuring the nip.
1159Fusing Jam Detection
SC Code Display
[0 to 1 / 0 / 1] 0:OFF, 1:ON
This SP setting determines whether SC559 is issued after three paper late jams occur in
the fusing unit. After this SP code is turned on, a counter monitors the number of paper
late jams that occur in the fusing unit. After the 3rd occurrence of a fusing jam, SC559 is
issued and the machine cannot be used until the service technician releases the error.
Note
• Switching the machine off/on does not reset this jam counter. The counter is reset
after the cause of the jam has been removed and a sheet of paper successfully
passes the fusing exit sensor.

SP1-xxx: Feed-2

1801*Motor Speed Adjustment
Adjusts the speeds of each motor. Each step decreases or increases motor speed in 0.05%
increments
Regist: Registration motor, Feed: Feed motor,
Duplex: Duplex/By-pass motor, Inverter: Duplex inverter motor,
Exit: Paper exit motor, Bridge: Bridge unit drive motor,
OpcMot: Drum motor, TransferMot: Transfer/Development Motor,
FusingMot: Fusing motor,
DevPuddleMot: Development Paddle motor
001 Regist: 90: Thick 2 [-2 to 2 / 0.4 / 0.05 %]
002 Regist: 154: Thick 1 [-2 to 2 / 0.4 / 0.05 %]
003 Regist: 180: Plain [-2 to 2 / 0.4 / 0.05 %]
004 Regist: 230: Plain [-2 to 2 / 0.4 / 0.05 %]
005 Feed: 90: Thick 2 [-2 to 2 / 0.4 / 0.05 %]
006 Feed: 154: Thick 1 [-2 to 2 / 0.4 / 0.05 %]
007 Feed: 180: Plain
[-2 to 2 / -1 / 0.05 %]
008 Feed: 230: Plain [-2 to 2 / -1 / 0.05 %]
009 Duplex_CW: 90: Thick 2 [-4 to 4 / 0.4 / 0.1 %]
010 Duplex_CW: 154: Thick 1 [-4 to 4 / 0.4 / 0.1 %]
011 Duplex_CW: 180: Plain [-4 to 4 / 2.3 / 0.1 %]
012 Duplex_CW: 230: Plain [-4 to 4 / 0.4 / 0.1 %]
013 Duplex_CCW: 90: Thick 2 [-4 to 4 / 0.4 / 0.1 %]
014 Duplex_CCW: 154: Thick 1 [-4 to 4 / 0.4 / 0.1 %]
015 Duplex_CCW: 180: Plain [-4 to 4 / 2.3 / 0.1 %]
016 Duplex_CCW: 230: Plain [-4 to 4 / 2.3 / 0.1 %]
017 Inverter_CW: 90: Thick 2 [-4 to 4 / 0 / 0.1 %]
Call Now Button
Show Buttons
Hide Buttons
X